Name

stoppedrules — The Shorewall file that governs what traffic flows through the firewall while it is in the 'stopped' state.

Synopsis

/etc/shorewall6/stoppedrules

Description

This file is used to define the hosts that are accessible when the firewall is stopped or is being stopped.

Warning

Changes to this file do not take effect until after the next shorewall start, shorewall restart, or shorewall compile command.

The columns in the file are as follows (where the column name is followed by a different name in parentheses, the different name is used in the alternate specification syntax).

ACTION - ACCEPT|NOTRACK

Determines the disposition of the packet.

ACCEPT means that the packet will be accepted.

NOTRACK indicates that no conntrack entry should be created for the packet. NOTRACK does not imply ACCEPT.

DROP was added in Shorewall 4.6.0 and causes the packet to be dropped in the raw table's PREROUTING chain.

SOURCE - [-|[$FW|interface]|[{$FW|interface}[:address[,address]...]]|[address[,address]...]

$FW matches packets originating on the firewall itself, while interface specifies packets arriving on the named interface.

This column may also include a comma-separated list of IP/subnet addresses. If your kernel and iptables include iprange match support, IP address ranges are also allowed. Ipsets and exclusion are also supported. When $FW or interface are specified, the list must be preceded by a colon (":").

If left empty or supplied as "-", ::/0 is assumed.

DEST - [-|[$FW|interface]|[{$FW|interface}[:address[,address]...]]|[address[,address]...]

$FW matches packets addressed the firewall itself, while interface specifies packets arriving on the named interface. Neither may be specified if the target is NOTRACK or DROP.

This column may also include a comma-separated list of IP/subnet addresses. If your kernel and iptables include iprange match support, IP address ranges are also allowed. Ipsets and exclusion are also supported. When $FW or interface are specified, the list must be preceded by a colon (":").

If left empty or supplied as "-", ::/0 is assumed.

PROTO (Optional) ‒ protocol-name-or-number[,...]

Protocol.

Beginning with Shorewall 4.5.12, this column can accept a comma-separated list of protocols.

DEST PORT(S) (dport) ‒ service-name/port-number-list

Optional. A comma-separated list of port numbers and/or service names from /etc/services. May also include port ranges of the form low-port:high-port if your kernel and iptables include port range support.

SOURCE PORT(S) (sport) ‒ service-name/port-number-list

Optional. A comma-separated list of port numbers and/or service names from /etc/services. May also include port ranges of the form low-port:high-port if your kernel and iptables include port range support.

Beginning with Shorewall 4.5.15, you may place '=' in this column, provided that the DEST PORT(S) column is non-empty. This causes the rule to match when either the source port or the destination port in a packet matches one of the ports specified in DEST PORTS(S). Use of '=' requires multi-port match in your iptables and kernel.

FILES

/etc/shorewall6/stoppedrules

See ALSO

http://www.shorewall.net/starting_and_stopping_shorewall.htm

http://www.shorewall.net/configuration_file_basics.htm#Pairs

shorewall(8), shorewall-accounting(5), shorewall-actions(5), shorewall-blacklist(5), shorewall-hosts(5), shorewall_interfaces(5), shorewall-ipsets(5), shorewall-maclist(5), shorewall-masq(5), shorewall-nat(5), shorewall-netmap(5), shorewall-params(5), shorewall-policy(5), shorewall-providers(5), shorewall-proxyarp(5), shorewall-rtrules(5), shorewall-rules(5), shorewall.conf(5), shorewall-secmarks(5), shorewall-tcclasses(5), shorewall-tcdevices(5), shorewall-tcrules(5), shorewall-tos(5), shorewall-tunnels(5), shorewall-zones(5)

Documentation


Frequently Used Articles

- FAQs - IPv4 Manpages - IPv6 Manpages - Configuration File Basics - Beginner Documentation - Troubleshooting

Shorewall 4.0/4.2 Documentation


Current HOWTOs and Other Articles

- 6to4 and 6in4 Tunnels - Accounting - Actions - Aliased (virtual) Interfaces (e.g., eth0:0) - Anatomy of Shorewall - Anti-Spoofing Measures - AUDIT Target support - Bandwidth Control - Blacklisting/Whitelisting - Bridge/Firewall - Building Shorewall from GIT - Commands - Compiled Programs - Configuration File Basics - DHCP - DNAT - Dynamic Zones - ECN Disabling by host or subnet - Events - Extension Scripts - Fallback/Uninstall - FAQs - Features - Fool's Firewall - Forwarding Traffic on the Same Interface - FTP and Shorewall - Helpers/Helper Modules - Installation/Upgrade - IPP2P - IPSEC - Ipsets - IPv6 Support - ISO 3661 Country Codes - Kazaa Filtering - Kernel Configuration - KVM (Kernel-mode Virtual Machine) - Limiting Connection Rates - Linux Containers (LXC) - Linux-vserver - Logging - Macros - MAC Verification - Manpages (IPv4) (IPv6) - Manual Chains - Masquerading - Multiple Internet Connections from a Single Firewall - Multiple Zones Through One Interface - My Shorewall Configuration - Netfilter Overview - Network Mapping - No firewalling of traffic between bridge port - One-to-one NAT - Operating Shorewall - OpenVPN - OpenVZ - Packet Marking - Packet Processing in a Shorewall-based Firewall - 'Ping' Management - Port Forwarding - Port Information - Port Knocking (deprecated) - Port Knocking, Auto Blacklisting and Other Uses of the 'Recent Match' - PPTP - Proxy ARP - QuickStart Guides - Release Model - Requirements - Routing and Shorewall - Routing on One Interface - Samba - Shorewall Events - Shorewall Init - Shorewall Lite - Shorewall on a Laptop - Shorewall Perl - Shorewall Setup Guide - SMB - SNAT - Split DNS the Easy Way - Squid with Shorewall - Starting/stopping the Firewall - Static (one-to-one) NAT - Support - Tips and Hints - Traffic Shaping/QOS - Simple - Traffic Shaping/QOS - Complex - Transparent Proxy - UPnP - Upgrade Issues - Upgrading to Shorewall 4.4 (Upgrading Debian Lenny to Squeeze) - VPN - VPN Passthrough - White List Creation - Xen - Shorewall in a Bridged Xen DomU - Xen - Shorewall in Routed Xen Dom0

Top of Page